A comprehensive checklist and reference guide for putting a subwoofer in your vehicle
by Crutchfield's Buck Pomerantz
May 29, 2024
It's a good idea to plan out the system completely, before you buy the gear.
When planning a bass system, customers ask every day about where they should start. Doing it properly takes some planning and forethought, especially if you're starting small and intend to expand over time.
How big of a subwoofer system will you need?
When putting together a bass system, the first questions to ask are:
- How much bass do I need?
- How many subwoofers?
- How much power?
The answers depend on the type of audio system you have currently, and what your end goals are. Estimate the power your subwoofer system may need in order for the bass to musically blend and balance well with your existing system. If you have:
- A factory radio — you won't need more than 50 to 200 watts RMS of power for the bass.
- An aftermarket receiver — you might want 200 to 300 watts RMS of power.
- Amplified speakers with around 50 watts RMS per channel — 250 to 500 watts RMS is a good starting point.
- A system with 100 watts RMS per channel — having at least 1,000 watts RMS, or more for the sub is not uncommon.
Focal RSB-300 Auditor Series 12" subwoofer
Choose a subwoofer and enclosure
The sound quality and volume of bass depends not only on the specific component sub you get, but also what style and size of enclosure it mounts in. For some background in what to look for in a subwoofer, see our Subwoofers FAQ. Then go to Subwoofer Enclosures article for help finding out which enclosure will work best for you. For further help in deciding which sub to get, you can look at our Subwoofer Shopping Guide.
Rockford Fosgate Punch P300X1
Choose an amplifier
Mono, 1-channel amplifiers are designed to work best with subwoofers and often feature filters and tone controls specifically made to handle bass. You will want an amp that can put out up to the subwoofer's top RMS wattage rating.
To learn more about amps, check out our Car Amplifiers FAQ. For help in picking which amp to get, see our Car Amplifier Shopping Guide.
Plan out the wiring scheme to be sure the sub and amp can work together
Subs come in different impedances, and in dual and single voice coil models, in order to work in a variety of systems. An amp puts out more power to a low impedance sub than to a higher impedance sub. So, to find out how much power an amp can deliver, you have to know how the sub will be wired. To make some sense of all this, you can refer to a couple of articles: Dual Voice Coil Subwoofers and Wiring Subwoofers — What's all this about Ohms?
You might need to adjust your choice of sub or amp, so they'll work together properly. Changing your set-up on paper is a lot less challenging than exchanging purchased gear. Check out the different ways subs get wired in our Subwoofer Wiring Diagrams. These diagrams can help you decide which method will work best for the gear you've chosen.
Sound Ordnance B-8PTD compact powered sub
A powered subwoofer is an easier solution
For many people, a small, self-contained, powered subwoofer will provide more than enough bass for their system. After positioning the powered sub, all you need to add are power cables and signal wires. You can learn more by watching the Crutchfield video on
MTX ThunderForm custom-fit powered subwoofer for 2004-08 Ford F-150 SuperCrew and SuperCab
Vehicle-specific enclosures with subs
Instead of the usual "sub-in-a-box," you might want to consider a vehicle-specific enclosure. Made to fit your car or truck, this enclosure contains a high-quality sub and fits into a convenient spot in your vehicle. Some enclosures even include a built-in amp, for the ultimate in stealth bass. You don't lose much (if any) space, the sub is perfectly matched to its enclosure, and it has a factory look that won't alert potential thieves to your expensive sound system. To see if there's a vehicle-specific enclosure for your car or truck, visit our vehicle selector.
Rockford Fosgate RFK4X 4-gauge wiring kit
Amp power wire kits
It is absolutely essential for an amplifier to receive its full share of electricity through large power wires, in order to operate properly and safely. The wattage of the amplifier determines what the proper size power wires should be. Amplifier manufacturers usually recommend a particular power cable size for each of their amps. Or, you can use our Cable Gauge Chart to figure out the power cable size that's best for your system.
Amp wiring kits contain most of what you need to hook up your amp. Some kits even come with signal wires, the RCA patch cords that allow the signal to get from the receiver to the sub amp.
Install Bay MANL50 Fuses
Fuses are for your safety
Always install the in-line power fuse near the battery. If something failed back by the amp, you don't want a live, high current wire stretched throughout your car and engine compartment, because it could possibly heat up and start a fire.
Crutchfield 4-Channel RCA Patch Cable
The signal wires
The music has to have a way to get from the receiver to your sub amp. If you have an aftermarket receiver, it probably has RCA outputs you can use. Plan on getting new, high-quality patch cables. If you have a receiver with no RCA outputs, you can tap into the existing factory speaker wires with new speaker wires, to use for a high-level input to your amp. The amp, of course, has to have a speaker-level input feature for this to work. To prevent noise, all signal wires should run through your vehicle as far away from any power cables as possible.
Stinger PRO Series 16-gauge speaker wire
The speaker wires
If your sub system is going to put out more than 1,000 watts RMS, you can use 12-gauge speaker wire. But 16-gauge speaker wire works well for most installations. Take a hint and order twice as much as you think you need. You never know when a sub or amp's position will need adjusting and you'll be thankful you have the extra length.
And don't forget tools
There are some tools and connectors that will make your sub installation much easier. Take a look at what you might need in our video on Car Stereo Installation Tools.
Gather the gear
Before you start working, make sure you have everything you need. You'll want to gather your component sub(s), enclosure, speaker wire, amplifier, (or a powered sub), an amp wiring kit, signal cables, and any tools you think will come in handy.
Pioneer Stage 4 system with two 10" subs
Now is the time to install it
To see how an amp installation is done, see our Amplifier Installation Guide, and watch our video on Installing a Car Amplifier. You can also check out the Subwoofer Installation Guide for more tips and suggestions.
Make sure you always disconnect the car battery's negative, ground cable before working on the electrical system. Also, make sure the fuse is out of the in-line fuse holder until the installation is complete. Only then should you re-connect the battery ground and install the fuse.
Test — does it turn on and off correctly?
Make sure all volumes and gains are set to their minimum, and make sure all filters are off or disengaged. The sub amp should come on when you turn on the receiver. If the amp stays on even after you turn off the ignition, then you need to go back and re-wire the remote turn-on lead correctly to a switched power source. An amp that's always on will drain your car's battery in a hurry.
Turn the gain up until it distorts, then back it off until the sound is clean again.
Tune your sub
Properly setting the gain and the filters of your sub amp is crucial to getting good bass without causing damage. See Tuning Your Subs for the "by ear" method of tuning your system. Another method involves using test tones and a multimeter to set the amp's gain to a target output voltage. Our Test Tones article helps explain that.
A lot of people notice changes in a new subwoofer's tone after a few months of play. Whether this "breaking in" period really effects the sub or not, a second tuning, a few months after the first, will make your ears happy.
Don't blow it
There are two ways to blow a sub. The first way is to over-power it: constantly playing music at a power level well beyond what the voice coil can stand. Eventually, it burns up.
The other method of blowing a sub doesn't involve power, but distortion, often called "clipping." That crumbling, crackling, gritty, or hissing sound can destroy a subwoofer no matter what the volume. There're a couple reasons why. One is that during the flat parts of a clipped signal, although plenty of current flows through the voice coil, there's no movement, and hence no cooling. When that happens, the coil overheats.
Another reason is that severely clipped waveforms force the sub's coil and cone to try to move at infinite speed when changing direction. That can't happen, and either the cone or the coil dies. Under-powering is often the contributing factor in a blown sub because a distorted signal gets applied in an attempt to get more volume.
T-Spec capacitor
Don't stress your vehicle's electrical system
Capacitors should only be used if your lights dim a little on hard bass hits. For more information, see Capacitors FAQ. If your lights dim a lot whenever the music plays, then your sound system is overwhelming your vehicle's electrical system, and could damage the battery and alternator. Refer to the article entitled Car Lights Dim When the Music Plays for some suggestions on how to solve that problem.
Rock on, but be cool
If your car stereo can be heard a block away, that's impressive -- but it might not make the best first impression. Enjoy your music, and share it with those who'll appreciate it, but don't infringe on someone else's right to peace and quiet.
Speaking of sharing, send us some photos of your finished installation. Our Custom Car Showroom is a great place to show off your system, or find inspiration for your next car audio project.
Jared S's 2004 Chevrolet Cavalier
Comments (48)
Please share your thoughts below.
-
Jeremy Butler from Greer
Posted on 11/27/2023
Question: I have two Rockford Fosgate T2500-1 bdCP amplifiers strapped together at 1 ohm total ohm load. I am running a dual voice coil subwoofer wired to 1 ohm, with an RMS output of 2,500 WRMS. I am actually planning to upgrade to another dual voice coil subwoofer at 1 ohm, with 4,000 WRMS. I see a great deal of content around lower powered systems and proper speaker wire. Currently, I am running 8 awg speaker wire now. Is this considered sufficient with the upgraded sub? For complete power, I have 2 runs of 1/0 AWG from front battery (upgraded XS Power AGM) to rear battery (large XS Power AGM & 500 Farad Cap), both fed by 370 amp alternator. Each RF amplifier has 1/0 AWG Power and Ground. All fused properly. Just questioning the speaker wire at this point. Thanks.
Buck Pomerantz from Crutchfield
on 11/28/2023
Jeremy, The Owner's Manual for that amp specs the speaker wire for a sub connected to two of the amps sync-ed together like you're doing at 8-gauge. It also specifies a 2-ohm minimum impedance load when powering a sub in that configuration.
-
RICH from MCHENRY
Posted on 2/10/2023
Hello, I'm looking for a DVC 10" Subwoofer to pair with my Sony DSX GS80 unit. The unit has a built-in amp that can push 80 watts rms at 2ohms on each channel. I'm wiring the front/rear speakers in parallel and using the 2 rear channels for each VC on the subwoofer. According to the sony manual, you can drive a sub in this configuration. The manual states that i need to use a 4-8ohm sub but i have to select 2ohm load in the unit prior to powering everything up. Can I use a dvc 2 ohm sub as well?
See AlsoSubwoofer wiring diagrams — how to hook up your subsAmplifier wiring diagrams: How to add an amplifier to your car audio systemSubwoofer wiring diagrams — how to hook up your subsWiring subwoofers what's all this about ohms?Buck Pomerantz from Crutchfield
on 2/10/2023
Rich, It isn't at all clear what output wattage the amplifier in this receiver will do with a 2-ohm load. According to the instructions, you should be fine hooking it up the way you describe - only don't expect much volume from the sub.
-
nick from belmont
Posted on 5/30/2022
Im running 2 skar evls 12in 1250 watts rms each. what size wire do i need to run from my skar amp to my subs? currently using 12 gauge. the amp is skar skv2 2500.1d = 2500 rms
Buck Pomerantz from Crutchfield
on 5/31/2022
Nick, For wiring subwoofers, we recommend using wires of 12- to 16-gauge in size.
-
Michael Johnson from Brooksville
Posted on 4/13/2022
hi i was wondering what kind of amp/amps i would need to run four tx65 max power 200 and 100 rms per set (so im getting two sets so i can run four of them) I also have tweeters as well. Also would like to add two vd-10 subs which are either daul 2 ohm or dual 4 ohm not sure which set to get they are 800watt total and 500 rms. Please help im new to amps and have no idea which amp or amps i need i would like to have only one amp to run the whole system but i hear that is not possible. please help me thank you.
Buck Pomerantz from Crutchfield
on 4/13/2022
Michael, It sounds like you're looking for a 5-channel amplifier. Give us a call, so an Advisor can help you pick the perfect amp for your system.
-
Lewis Lennox from Nairobi
Posted on 12/15/2020
Hello. I recently bought a DVD Home theater Philips HTS3410D whose total power output power is 700W. It's a second hand and lacks the subwoofer. Can I get 1000 W subwoofer to replace it?
Buck Pomerantz from Crutchfield
on 12/15/2020
Lewis, I think you'll have to check in with Philips for a replacement subwoofer for your system.
-
sonny from atascadero
Posted on 12/4/2020
i have a kicker comp r subwoofer with 500 watt rms with 1000 peak at 2 ohms and i'm looking for a good amp do you have any suggestions
-
Jaeden Roxas from Adelaide, Australia
Posted on 10/27/2020
Hi,Was Wondering what size cable to run to my x2-400w (rms), 4 ohm dvc sub woofers, are there any formulae you use to determine this? I understand that 16 gauge would work, but would I gain any real audible performance by using 12 Gauge etc.? Cheers
Buck Pomerantz from Crutchfield
on 10/27/2020
Jaeden, For wiring subwoofers, we recommend using wires of 12- to 16-gauge in size. There will be no audible difference between them - just less power loss with larger wire.
-
Craig Donahue from Macon
Posted on 10/15/2020
I'm currently running (6 gauge wire) from my amp to one 12"sub.My question is I upgraded to a rockville 1000 rms amp and one 15" DS18 subwoofer 900 rms watts.(Do I need to change my 6 gauge to 4 gauge)?
Buck Pomerantz from Crutchfield
on 10/16/2020
Craig, If you're talking about speaker wire between the amp's output terminals and the sub's wiring terminals, then 6-gauge is already wildly over-doing it and you won't need any upgrading. If you're talking about power and ground wiring, then you might need to upgrade to 4-ga.
-
Dylan Harper from London
Posted on 10/11/2020
Is it OK o run a 300 watt sub, off one of the four channels of my amp which is rated at 65 watts per channel. The front speakers are on components so only using two channels for the fronts
Buck Pomerantz from Crutchfield
on 10/13/2020
Dylan, Without knowing precisely what amp and sub you're referring to, we can't help you with advice. If you want a question answered about a system, you must identify the gear by brand names and model numbers so we can get the correct information to you.
-
William Schroeder from South Milwaukee
Posted on 3/4/2020
So we just put 2 pioneer 10 inch subs in my girlfriends Honda Accord with a Evo2 amp... her car is a 2017 and we are running the subs with a stock head unit and just running a reviver instead of off the radio, but when all doors are closed the subs starts hitting super hard, constant wounds no fluctuation in power, but as soon as you open a door or break the current of the vehicle the subs stop.. what could this be?
Buck Pomerantz from Crutchfield
on 3/5/2020
William, Your Honda has an active noise cancellation (ANC) system which reacts poorly with subwoofers. You might look into disabling it. Do an online search for disabling the ANC in a Honda Accord and I'm sure you can find someone online to show you how to do that.
The easiest way to shop car audio online
Find what Fits your vehicle
Remove
Checking fit...
Related products
Loading...
Adding...
$189.99
Loading...
Adding...
$249.99
Loading...
Adding...
$479.95
Loading...
Adding...
$139.99
Related articles & videos
See all
- Car subwoofer buying guide Our subwoofer shopping guide will help you determine which kind of subwoofer and bass system you need to get the sound you want. by Crutchfield's Bob B.
- How to match subwoofers and amplifiers This step-by-step guide will help you make sure that your amps and subs are evenly matched and work well together. We explain how to select one to go with the other. by Crutchfield's Buck P.
- Tuning your subs What does the gain control do anyway? How should you set the low-pass filter? This article describes how to tune your amplifier so that your subwoofer sounds just the way you want it to. by Crutchfield's Buck P.
- What are dual voice coil subwoofers? Dual voice coil subwoofers are a popular choice among car audio enthusiasts who want more flexibility in wiring their sound systems. by Crutchfield's Bob B.
- How to choose a subwoofer box Subwoofers in sealed boxes play "tight" bass, while ported boxes sound "boomy." Which type you need depends on the style of music you like and how you want it to sound. by Crutchfield's Buck P.
- Subwoofers FAQ Which subwoofer will sound the loudest? Or the deepest? Which hits harder: one 12" sub or two 10" subs? How much power do I need? These answers and more in our FAQ. by Crutchfield's Crutchfield Writing Team
- Subwoofer wiring diagrams There are many ways to connect subwoofers to an amplifier. Our wiring diagrams will help you find the best way to wire your subs and amps so you'll get the most powerful performance out of your gear. by Crutchfield's Buck P.
- How to build a subwoofer box Helpful tips and step-by-step instructions for designing and building your own custom subwoofer box. We walk you through the math and the actual build in detail, so you'll know how to do it yourself. by Crutchfield's Robert F.
- Headlights dim when the music plays Here we discuss the most popular fixes for an underpowered electrical system: the big 3 upgrade, a capacitor, a high output alternator, and a second battery. by Crutchfield's Buck P.
Compare the sound
SpeakerCompare™
Patented Virtual Audio™ technology for auditioning speakers online
Recommended
You can change this setting any time by clicking 'Headphones' in the main menu.
Don't see your headphones?
Rent our Listening Kit
SpeakerCompare™ is protected by patents and patent applications owned by Crutchfield Corporation.
SpeakerCompare™
Patented Virtual Audio™ technology
Audition speakers before you buy
SpeakerCompare simulates the sound of home and car speakers through your headphones. It lets you compare sonic characteristics between speakers so that you can make a more informed shopping decision.
To get started: For the best sound comparison, we recommend selecting your brand and model of headphones in the right-hand column, or if your headphones aren't listed, you can rent one of our Listening Kits.
SpeakerCompare™ is protected by patents and patent applications owned by Crutchfield Corporation.
Please select a track to continue
SpeakerCompare™
...
What to listen for
Track notes
Artist
- analyzer
- log
- linear
- messages
We're here to help
For free personalized advice, call 1-888-291-8923. Our Advisors have listened to most of the speakers we carry, and can help you make the best choice for your system.
We'd love to know what you think
Select your headphones
Recommended
You can change this setting any time by clicking 'Headphones' in the main menu.
Don't see your headphones?
Rent our Listening Kit
Select a track to start listening
Audition speakers before you buy
SpeakerCompare simulates the sound of home and car speakers through your headphones. It lets you compare sonic characteristics between speakers so that you can make a more informed shopping decision.
Why selecting your headphones is important
SpeakerCompare tailors your listening experience to the exact headphones you have, so that what you hear is comparable to auditioning speakers side-by-side in person. Knowing which model headphones you’re using lets us remove any sonic coloring from your experience.
Two different listening modes
In an actual listening room, you'd find that some speakers play louder than others when fed the same amount of power. In equal power mode, you'll hear these differences in loudness as they naturally occur between speakers.
In equal volume mode, we've made the loudness of each speaker about the same. This gives you a more direct comparison of subtle voicing differences between speakers.
Nothing beats listening to speakers in your space
SpeakerCompare gives you a sense of the sonic differences. But performance in the real world is affected by the acoustics of your car or home, your choice of amplification, and your source material. We still believe that the gold standard for auditioning speakers is hearing them in your own environment — that’s why we offer a 60-day money-back guarantee.
Our Listening Kit
To help you choose the right speakers, we recommend using Crutchfield’s SpeakerCompare Listening Kit. It includes a pair of studio-quality headphones, and a guide to getting the most out of your session, and a few other necessary items. We’ve carefully chosen the components of this kit to ensure a crystal-clear listening experience. It’s available for a nominal rental fee, and includes a $25 Crutchfield merchandise credit.
Request a kit
Rate your experience with SpeakerCompare
Thank you for your feedback!
We'd love to know what you think